New 300-165 exam questions from PassLeader 300-165 dumps! Welcome to download the newest PassLeader 300-165 VCE and PDF dumps: https://www.passleader.com/300-165.html (275 Q&As –> 315 Q&As –> 330 Q&As –> 349 Q&As)
P.S. New 300-165 dumps are available on Google Drive shared by PassLeader: https://drive.google.com/open?id=0B-ob6L_QjGLpMVRmUUJZRWU3cU0
Read More CCNP Data Center Exam Dumps:
CCNP Data Center 300-160 Exam Dumps: http://www.ciscovceplus.com/?s=300-160
CCNP Data Center 300-170 Exam Dumps: http://www.ciscovceplus.com/?s=300-170
CCNP Data Center 300-175 Exam Dumps: http://www.ciscovceplus.com/?s=300-175
CCNP Data Center 300-180 Exam Dumps: http://www.ciscovceplus.com/?s=300-180
QUESTION 46
Between which two types of ports does FIP establish Fibre Channel virtual links? (Choose two.)
A. VE Ports and VE Ports
B. N Ports and F Ports
C. VN Ports and VF Ports
D. VP Ports and VE Ports
E. VE Ports and VF Ports
F. E Ports and E Ports
Answer: AC
Explanation:
FIP aims to establish virtual FC links between VN_Ports and VF_Ports (ENode to FCF), as well as between pairs of VE_Ports (FCF to FCF), since these are the only legal combinations supported by native Fibre Channel fabrics. Standards-compliant implementations are not required to support both forms of virtual FC links, and Cisco has decided to focus initially on implementing FIP only between ENodes and FCFs. FCF-to-FCF connectivity is considered a strategic direction for end-to-end FCoE deployments, but the short-term urgency is for FCoE adoption between CNAs and the Fibre Channel fabric perimeter, where unified fabric can offer the greatest capital expenditure (CapEx) savings today.
http://www.cisco.com/c/en/us/products/collateral/switches/nexus-7000-series-switches/white_paper_c11-560403.html
QUESTION 47
Which FCoE component is responsible for the encapsulation and de-encapsulation of Fibre Channel frames in Ethernet?
A. Distributed FCF
B. FCoE node
C. FCoE logical endpoint
D. Fibre Channel forwarder
E. FCoE forwarder
Answer: C
Explanation:
The FCoE Logical Endpoint (FCoE_LEP) is responsible for the encapsulation and deencapsulation functions of the FCoE traffic. FCoE_LEP has the standard Fibre Channel layers, starting with FC-2 and continuing up the Fibre Channel Protocol stack.
https://www.safaribooksonline.com/library/view/ccna-data-center/9780133860429/ch11lev3sec5.html
QUESTION 48
Which item represents the process that allows FCoE multihop using T11 standard FC-BB-5?
A. Distributed FCF
B. FIP proxy
C. N Port proxy
D. FIP snooping
Answer: D
Explanation:
FIP snooping is used in multi-hop FCoE environments. FIP snooping is a frame inspection method that can be used by FIP snooping capable DCB devices to monitor FIP frames and apply policies based on the information in those frames. This allows for:
– Enhanced FCoE security (Prevents FCoE MAC spoofing)
– Creates FC point-to-point links within the Ethernet LAN
– Allows auto-configuration of ACLs based on name server information read in the FIP frames
http://www.definethecloud.net/fcoe-initialization-protocol-fip-deep-dive/
QUESTION 49
How does an FCoE end node acquire its FCoE MAC address?
A. server-provided MAC address
B. Fibre Channel name server
C. fabric-provided MAC address
D. FIP proxy
Answer: C
Explanation:
The VN_Port is assigned a fabric-provided Mac address (FPMA) that is built by concatenating a 24-bit FCoE MAC address prefix (FC-MAP), ranging from 0x0E-FC-00 to 0x0E-FC-FF, to the 24-bit FCID. Being able to build a unique MAC address for the VN_Port directly from its FCID saves the switch from having to maintain a table that associates FCID and MAC addresses.
http://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/Data_Center/UF_FCoE_final.html
QUESTION 50
What mode is required on a Cisco Nexus 7000 32-port 10-GB module port group to allow equal access to the 10-GB port controller?
A. dedicated
B. assigned
C. shared
D. community
Answer: C
Explanation:
You can share 10 Gb of bandwidth among a group of ports (four ports) on a 32-port 10-Gigabit Ethernet module. To share the bandwidth, you must bring the dedicated port administratively down, specify the ports that are to share the bandwidth, change the rate mode to shared, and then bring the ports administratively up.
http://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/5_x/nx-os/interfaces/configuration/guide/if_cli/if_basic.html#70242
QUESTION 51
Which SCSI terminology is used to describe source and destination nodes?
A. hosts and targets
B. initiators and targets
C. HBA and disks
D. initiators and disks
E. HBA and targets
Answer: B
Explanation:
In computer data storage, a SCSI initiator is the endpoint that initiates a SCSI session, that is, sends a SCSI command. The initiator usually does not provide any Logical Unit Numbers (LUNs). On the other hand, a SCSI target is the endpoint that does not initiate sessions, but instead waits for initiators’ commands and provides required input/output data transfers. The target usually provides to the initiators one or more LUNs, because otherwise no read or write command would be possible.
http://en.wikipedia.org/wiki/SCSI_initiator_and_target
QUESTION 52
Which protocol is responsible for the discovery of FCoE capabilities on a remote switch?
A. DCE
B. DCBx
C. CDP
D. LLDP
Answer: B
Explanation:
Data Center Bridging Capabilities Exchange Protocol (DCBX): a discovery and capability exchange protocol that is used for conveying capabilities and configuration of the above features between neighbors to ensure consistent configuration across the network. This protocol leverages functionality provided by IEEE 802.1AB (LLDP). It is actually included in the 802.1az standard.
http://en.wikipedia.org/wiki/Data_center_bridging
QUESTION 53
Which two items are services that are provided by Cisco Fabric Services? (Choose two.)
A. Device alias distribution
B. VLAN database distribution
C. Kerberos proxy distribution
D. RSA key pair distribution
E. DPVM configuration distribution
Answer: AE
Explanation:
The device alias application uses the Cisco Fabric Services (CFS) infrastructure to enable efficient database management and distribution. Device aliases use the coordinated distribution mode and the fabric-wide distribution scope. DPVM can use CFS to distribute the database to all switches in the fabric. This allows devices to move anywhere and keep the same VSAN membership. You should enable CFS distribution on all switches in the fabric. Using the CFS infrastructure, each DPVM server learns the DPVM database from each of its neighboring switches during the ISL bring-up process. If you change the database locally, the DPVM server notifies its neighboring switches, and that database is updated by all switches in the fabric.
http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5000/sw/configuration/guide/cli/CLIConfigurationGuide/ddas.html
http://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/nx-os/san_switching/configuration/guide/b_Cisco_Nexus_7000_NX-OS_SAN_Switching_Configuration_Guide/Cisco_Nexus_7000_NX-OS_SAN_Switching_Configuration_Guide_chapter4.html#concept_2B83E16506C845B39BDF96F9CAFFAEC3
QUESTION 54
On a Cisco Nexus 7000 Series router, which statement about HSRP and VRRP is true?
A. When VDCs are in use, only VRRP is supported.
B. HSRP and VRRP both use the same multicast IP address with different port numbers.
C. HSRP has shorter default hold and hello times.
D. The VRRP group IP address can be the same as the router-specific IP address.
Answer: D
Explanation:
VRRP allows for transparent failover at the first-hop IP router by configuring a group of routers to share a virtual IP address. VRRP selects a master router in that group to handle all packets for the virtual IP address. The remaining routers are in standby and take over if the master router fails.
http://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/5_x/nx-os/unicast/configuration/guide/l3_cli_nxos/l3_vrrp.html
QUESTION 55
Refer to the exhibit. This multilayer Cisco Nexus switch had been the active virtual gateway for Group 1 before it became temporarily unavailable. What will happen to GLBP Group 1 when this device becomes available again?
A. The currently active router remains active.
B. It depends on the priority value that is configured active on the router.
C. The Cisco Nexus switch becomes the active virtual gateway after 600 seconds.
D. It depends on the weighting values that are configured active on the router.
Answer: A
Explanation:
GLBP prioritizes gateways to elect an active virtual gateway (AVG). If multiple gateways have the same priority, the gateway with the highest real IP address becomes the AVG. The AVG assigns a virtual MAC address to each member of the GLBP group. Each member is the active virtual forwarder (AVF) for its assigned virtual MAC address, forwarding packets sent to its assigned virtual MAC address. The AVG also answers Address Resolution Protocol (ARP) requests for the virtual IP address. Load sharing is achieved when the AVG replies to the ARP requests with different virtual MAC addresses.
Note:
Packets received on a routed port destined for the GLBP virtual IP address terminate on the local router, regardless of whether that router is the active GLBP router or a redundant GLBP router. This termination includes ping and Telnet traffic. Packets received on a Layer 2 (VLAN) interface destined for the GLBP virtual IP address terminate on the active router.
QUESTION 56
Which function does the graceful restart feature allow a Cisco Nexus 7000 Series router to perform?
A. Perform a rapid route convergence.
B. Initialize a standby supervisor transparently when one is present.
C. Remain in the data forwarding path through a process restart.
D. Maintain a management connection throughout a router restart.
Answer: C
Explanation:
Graceful Restart and Non Stop Routing both allow for the forwarding of data packets to continue along known routes while the routing protocol information is being restored (in the case of Graceful Restart) or refreshed (in the case of Non Stop Routing) following a processor switchover. When Graceful Restart is used, peer networking devices are informed, via protocol extensions prior to the event, of the SSO capable routers ability to perform graceful restart. The peer device must have the ability to understand this messaging. When a switchover occurs, the peer will continue to forward to the switching over router as instructed by the GR process for each particular protocol, even though in most cases the peering relationship needs to be rebuilt. Essentially, the peer router will give the switching over router a “grace” period to re-establish the neighbor relationship, whilecontinuing to forward to the routes from that peer.
http://www.cisco.com/c/en/us/products/collateral/ios-nx-os-software/high-availability/solution_overview_c22-487228.html
QUESTION 57
In policy-based routing, which action is taken for packets that do not match any of the route-map statements?
A. forwarded after the egress queue empties on the outbound interface
B. forwarded using the last statement in the route map
C. forwarded using the closest matching route-map statement
D. forwarded using destination-based routing
Answer: D
Explanation:
Each entry in a route map contains a combination of match and set statements. The match statements define the criteria for whether appropriate packets meet the particular policy (that is, the conditions to be met). The set clauses explain how the packets should be routed once they have met the match criteria. You can mark the route-map statements as permit or deny. You can interpret the statements as follows:
– If the statement is marked as permit and the packets meet the match criteria, the set clause is applied. One of these actions involves choosing the next hop.
– If a statement is marked as deny, the packets that meet the match criteria are sent back through the normal forwarding channels, and destination-based routing is performed.
– If the statement is marked as permit and the packets do not match any route-map statements, the packets are sent back through the normal forwarding channels, and destination-based routing is performed.
http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus9000/sw/7-x/unicast/configuration/guide/l3_cli_nxos/l3pbr.pdf
QUESTION 58
What must be enabled on the interface of a multicast-enabled device to support the Source Specific Multicast feature?
A. IGMP version 3
B. IGMP version 2
C. IGMP version 1
D. PIM
Answer: A
Explanation:
IGMP is the Internet Engineering Task Force (IETF) standards track protocol used for hosts to signal multicast group membership to routers. Version 3 of this protocol supports source filtering, which is required for SSM. To run SSM with IGMPv3, SSM must be supported in the Cisco IOS router, the host where the application is running, and the application itself. IGMP v3lite and URD are two Cisco-developed transition solutions that enable the immediate development and deployment of SSM services, without the need to wait for the availability of full IGMPv3 support in host operating systems and SSM receiver applications. IGMP v3lite is a solution for application developers that allows immediate development of SSM receiver applications switching to IGMPv3 as soon as it becomes available. URD is a solution for content providers and content aggregators that enables them to deploy receiver applications that are not yet SSM enabled (through support for IGMPv3). IGMPv3, IGMP v3lite, and URD interoperate with each other, so that both IGMP v3lite and URD can easily be used as transitional solutions toward full IGMPv3 support in hosts.
http://www.cisco.com/c/en/us/td/docs/ios/12_2/ip/configuration/guide/fipr_c/1cfssm.html
QUESTION 59
Which two statements about implementing Cisco NPV and NPIV on a Cisco Nexus 5000 Series switch are true? (Choose two.)
A. STP must run inside the FP network.
B. All VLANs must be in the same mode, CE, or FP.
C. FP port can join the private and nonprivate VLANs.
D. Only F and M series modules can run FabricPath.
E. These require an enhanced Layer 2 license to run.
Answer: BE
Explanation:
With the Nexus 5×00 switch, FCoE functionality is a licensed feature. After the license is installed, FCoE configuration can be completed.
http://www.ciscopress.com/articles/article.asp?p=2030048&seqNum=4
QUESTION 60
What is the Overlay Transport Virtualization site VLAN used for?
A. to allow the join interfaces at different sites to communicate
B. to detect devices at the site that are not capable of OTV
C. to allow multiple site AEDs to communicate with each other
D. to facilitate communications between OTV edge devices within the site
Answer: D
New 300-165 exam questions from PassLeader 300-165 dumps! Welcome to download the newest PassLeader 300-165 VCE and PDF dumps: https://www.passleader.com/300-165.html (275 Q&As –> 315 Q&As –> 330 Q&As –> 349 Q&As)
P.S. New 300-165 dumps are available on Google Drive shared by PassLeader: https://drive.google.com/open?id=0B-ob6L_QjGLpMVRmUUJZRWU3cU0
Read More CCNP Data Center Exam Dumps:
CCNP Data Center 300-160 Exam Dumps: http://www.ciscovceplus.com/?s=300-160
CCNP Data Center 300-170 Exam Dumps: http://www.ciscovceplus.com/?s=300-170
CCNP Data Center 300-175 Exam Dumps: http://www.ciscovceplus.com/?s=300-175
CCNP Data Center 300-180 Exam Dumps: http://www.ciscovceplus.com/?s=300-180