web analytics

Free PassLeader 644-906 Exam Dumps with VCE and PDF Download (Question 6 – Question 10)

New 644-906 exam questions from PassLeader 644-906 dumps! Welcome to download the newest PassLeader 644-906 VCE and PDF dumps: http://www.passleader.com/644-906.html (80 Q&As)

P.S. Free 644-906 dumps are available on Google Drive shared by PassLeader: https://drive.google.com/open?id=0B-ob6L_QjGLpRG5BVlFadVpfZzg

QUESTION 6
When running MPLS Traffic Engineering with Cisco IOS XR Software, which three criteria can be seen when the show mpls traffic-eng tunnels command is executed on a midpoint router? (Choose three.)

A.    tunnel role
B.    TE metric
C.    tunnel ID
D.    physical bandwidth
E.    incoming and outgoing label

Answer: ACE

QUESTION 7
What are the two prerequisites for enabling multicast-only fast reroute (MoFRR) in a network? (Choose two.)

A.    There must be an Equal-Cost Multipath (ECMP) topology.
B.    IP multicast traffic must use the group address 232.0.0.0/8.
C.    PIM-SSM needs to be configured.
D.    There must be a valid reverse path back to the multicast source.

Answer: AD

QUESTION 8
Which CLI command can be used to display interfaces statistics?

A.    RP/0/RSP1/CPU0:ASR9006#monitor interface
B.    RP/0/RSP1/CPU0:ASR9006#show interfaces summary
C.    RP/0/RSP1/CPU0:ASR9006#show interfaces statistics | inc errors
D.    RP/0/RSP1/CPU0:ASR9006#show interfaces accounting | inc errors
E.    RP/0/RSP1/CPU0:ASR9006(admin)#show flow platform producer statistics location 0/0/CPU0
F.    RP/0/RSP1/CPU0:ASR9006(admin)##show interfaces statistics

Answer: A

QUESTION 9
Which three types of packet drop statistics can be determined by using the following Cisco IOS XR CLI show command? (Choose three.)
RP/0/RSP1/CPU0:ASR9006-A#show cef ipv4 drops location all

A.    no route drops
B.    no adjacency drops
C.    RPF drops
D.    ACL drops
E.    asymmetric routing drops
F.    Cisco Express Forwarding exception drops

Answer: ABC

QUESTION 10
Referring to the configuration output exhibit, which set of commands below will allow you to insert a new line just before the permit any statement?
passleader-644-906-dumps-101

A.    :router#configure
:router(config)#ipv4 access-list Ethernet_In
:router(config-ipv4-acl)# 2.5 deny udp any eq tftp any
B.    :router#configure
:router(config)#ipv4 access-list Ethernet_In
:router(config-ipv4-acl)# insert after 2 deny udp any eq tftp any
C.    :router #resequence access-list ipv4 Ethernet_In
:router#configure
:router(config)#ipv4 access-list Ethernet_In
:router(config-ipv4-acl)#25 deny udp any eq tftp any
D.    :router#configure
:router(config)#ipv4 access-list Ethernet_In
:router(config-ipv4-acl)#move 3 to 4
:router(config-ipv4-acl)#3 deny udp any eq tftp any

Answer: C


New 644-906 exam questions from PassLeader 644-906 dumps! Welcome to download the newest PassLeader 644-906 VCE and PDF dumps: http://www.passleader.com/644-906.html (80 Q&As)

P.S. Free 644-906 dumps are available on Google Drive shared by PassLeader: https://drive.google.com/open?id=0B-ob6L_QjGLpRG5BVlFadVpfZzg