New 642-035 exam questions from PassLeader 642-035 dumps! Welcome to download the newest PassLeader 642-035 VCE and PDF dumps: http://www.passleader.com/642-035.html (175 Q&As)
P.S. Free 642-035 dumps are available on Google Drive shared by PassLeader: https://drive.google.com/open?id=0B-ob6L_QjGLpflF3ZkRqdFc0WFQ3VGFsejB5M05sX1QxczkxcU90V0d3dnVLOXYtb1AyWHM
QUESTION 76
In new Cisco UCS release 2.0 installations, what are the default VLAN IDs?
A. Ethernet VLAN default ID is 4048, FCOE default VLAN ID 4048
B. Ethernet VLAN default ID is 1, FCOE default VLAN ID is 3968
C. Ethernet VLAN default ID is 1, FCOE default VLAN ID is 2
D. Ethernet VLAN default ID is 2, FCOE default VLAN ID is 4047
E. Ethernet VLAN default ID is 1, FCOE default VLAN ID is 4048
Answer: E
QUESTION 77
If a server is not associated with a service profile, the activated firmware remains pending. Which two steps should you take? (Choose two.)
A. Manually reboot the server.
B. Reset the server to a new profile.
C. Reset the unassociated server to activate the firmware.
D. Reinitialize the firmware process with Cisco UCS Manager.
E. Download the firmware and start over.
F. Shut down gracefully and start over.
Answer: AC
QUESTION 78
After migrating a server that is configured with dynamic vNICs, Cisco UCS Manager assigns new dynamic vNICs to the server. If you had been monitoring traffic on an original dynamic vNIC, what must you do when the server comes back up?
A. Reassign the dynamic vNIC back to the old configuration.
B. Nothing; Cisco UCS Manager will take over.
C. Reassign the service profile back to the master one.
D. Remove and reconfigure the dynamic vNIC.
E. Reassign the monitoring source.
Answer: E
QUESTION 79
Which two Cisco Nexus 2000-Series Fabric Extenders support connections to both Cisco Nexus 5000 Series Switches and Cisco Nexus 7000 Series Switches? (Choose two.)
A. Cisco Nexus 2248TP
B. Cisco Nexus 2248TP-E
C. Cisco Nexus 2232PP
D. Cisco Nexus 2232TM
Answer: AC
QUESTION 80
UCS-A# scope eth-uplink
UCS-A /eth-uplink # scope fabric a
UCS-A /eth-uplink/fabric # scope interface 2 3
UCS-A /eth-uplink/fabric/interface # create mon-src Monitor23
UCS-A /eth-uplink/fabric/interface/mon-src* # set direction receive
UCS-A /eth-uplink/fabric/interface/mon-src* # commit-buffer
What does the command scope interface 2 3 in the above CLI command sequence do on a Cisco UCS blade server?
A. enters the interface command mode for the specified uplink port
B. enters the interface command mode for the specified Fabric A
C. enters the interface command mode for the specified Fabric B
D. enters slot 3 port 2 specified uplink port
Answer: A
QUESTION 81
For a KVM session to be successful, which two of these need to be done? (Choose two.)
A. The Cisco IMC IP address needs to be assigned on the Admin tab.
B. The Cisco IMC IP address needs to be in the same subnet as the management IP.
C. The Cisco IMC needs to be upgraded to the same version as the UCS Manager.
D. The server needs to be fully discovered.
Answer: AD
QUESTION 82
A customer is configuring SAN pin groups in a Cisco UCS domain. The customer notices that pinning is not working and traffic from the vHBA is not passing over the Fibre Channel uplink port. Which of these must be done for pinning to work correctly?
A. Include the SAN pin group in a vHBA policy and then include the vHBA policy in the service profile that is assigned to that server.
B. Include the SAN policy in the Cisco UCS Manager to match with pin groups on the fabric interconnect.
C. The customer must have Cisco UCS Manager version 2.0 or above.
D. Fibre Channel switch mode needs to be configured first.
Answer: A
QUESTION 83
Refer to exhibit. A Cisco UCS admin is troubleshooting an issue with a vNIC not coming up on a blade. When looking at the CLI of the “Fabric Interconnect”,the admin runs this command to view the status of the interface. Which option describes a possible reason why the interface is stuck in an “initializing” state?
A. The service profile is not applied to a blade.
B. The VLANs defined on the vNIC are not defined on a matching uplink port.
C. The uplink port is down.
D. The QoS policy on the vNIC is invalid.
E. The MTU on the vNIC is higher than the MTU configured in the QoS system class.
Answer: C
QUESTION 84
Which two options are causes for failure of a Cisco C-Series server that is configured to boot from SAN? (Choose two.)
A. The boot LUN ID is not 0.
B. The ISCSI target is only available via one via one path through the network.
C. C-Series does not support boot from SAN.
D. The KVM dongle is attached to the front of the server with a USB stick installed.
E. Under the FCoE properties on the vNIC adapter, the FCoE VLAN ID is set to 10.
F. The boot table for fc0 has not been configured.
Answer: DF
QUESTION 85
Which command on the Fabric Interconnect displays packet statistics for a given QoS group and MTU size?
A. show policy-map interface ethernet x/y
B. show queuing interface ethernet x/y
C. show interface ethernet x/y
D. show class-map type qos
E. show interface queuing ethernet x/y
Answer: B
New 642-035 exam questions from PassLeader 642-035 dumps! Welcome to download the newest PassLeader 642-035 VCE and PDF dumps: http://www.passleader.com/642-035.html (175 Q&As)
P.S. Free 642-035 dumps are available on Google Drive shared by PassLeader: https://drive.google.com/open?id=0B-ob6L_QjGLpflF3ZkRqdFc0WFQ3VGFsejB5M05sX1QxczkxcU90V0d3dnVLOXYtb1AyWHM