web analytics

200-601 PDF Dumps

[23-Aug-2018] New 200-601 Dumps with VCE and PDF from PassLeader (Update Questions)

New 200-601 exam questions from PassLeader 200-601 dumps! Welcome to download the newest PassLeader 200-601 VCE and PDF dumps: https://www.passleader.com/200-601.html (90 Q&As)

P.S. New 200-601 dumps are available on Google Drive shared by PassLeader: https://drive.google.com/open?id=0B-ob6L_QjGLpekY2NnBTTzFpejQ

NEW QUESTION 71
Refer to the exhibit. CCNA.com has the industrial network shown in the exhibit. All switches are configured as layer 2 switches and are using VLAN 1 as their management VLAN. Each VLAN 1 interface has been assigned the correct IP address. What is the purpose of assigning a default gateway to SW-C switch?
passleader-200-601-dumps-711

A.    allows connectivity between the VLAN 1 interface on SW-C and other devices in the network.
B.    allows connectivity between Host A and other devices in the network.
C.    allows connectivity between Host B and other devices in the network.
D.    allows the switch to pass traffic between Host A and Host B.

PassLeader 200-601 Exam Dumps Collection with VCE and PDF (Question 36 – Question 40)

New 200-601 exam questions from PassLeader 200-601 dumps! Welcome to download the newest PassLeader 200-601 VCE and PDF dumps: http://www.passleader.com/200-601.html (70 Q&As –> 90 Q&As)

P.S. Free 200-601 dumps are available on Google Drive shared by PassLeader: https://drive.google.com/open?id=0B-ob6L_QjGLpekY2NnBTTzFpejQ

QUESTION 36
To ensure ProfiNET Layer 2 Class-of-Service markings from ProfiNET devices are trusted by the switch, which command must be entered on the interface attached to the device?

A.    switch(config-if)#mls qos trust cos
B.    switch(config-if)#qos trust cos
C.    switch(config-if)#profinet cos trust
D.    switch(config-if)#trust qos cos

PassLeader Valid 200-601 Dumps with VCE and PDF (Question 31 – Question 35)

New 200-601 exam questions from PassLeader 200-601 dumps! Welcome to download the newest PassLeader 200-601 VCE and PDF dumps: http://www.passleader.com/200-601.html (70 Q&As –> 90 Q&As)

P.S. Free 200-601 dumps are available on Google Drive shared by PassLeader: https://drive.google.com/open?id=0B-ob6L_QjGLpekY2NnBTTzFpejQ

QUESTION 31
Which CLI command will display IGMP snooping information in a Cisco IE2000 or Stratix 5700 switch?

A.    switch#show snooping ip igmp
B.    switch#show igmp snooping
C.    switch#show ip igmp snooping
D.    switch#show ip snooping

Update 200-601 Dumps with VCE and PDF for Free (Question 26 – Question 30)

New 200-601 exam questions from PassLeader 200-601 dumps! Welcome to download the newest PassLeader 200-601 VCE and PDF dumps: http://www.passleader.com/200-601.html (70 Q&As –> 90 Q&As)

P.S. Free 200-601 dumps are available on Google Drive shared by PassLeader: https://drive.google.com/open?id=0B-ob6L_QjGLpekY2NnBTTzFpejQ

QUESTION 26
Which five are characteristics that describe Cisco Industrial switches? (Choose five.)

A.    Din rail mount
B.    19 inch rack mount
C.    Fanless
D.    Fans
E.    Swappable SD flash card
F.    Alarm relay
G.    -5ºC to 45ºC operating environment
H.    ProfiNET conformance class C compliance

100% Pass Ensure 200-601 Dumps with Free VCE and PDF (Question 21 – Question 25)

New 200-601 exam questions from PassLeader 200-601 dumps! Welcome to download the newest PassLeader 200-601 VCE and PDF dumps: http://www.passleader.com/200-601.html (70 Q&As –> 90 Q&As)

P.S. Free 200-601 dumps are available on Google Drive shared by PassLeader: https://drive.google.com/open?id=0B-ob6L_QjGLpekY2NnBTTzFpejQ

QUESTION 21
A ProfiNET management system operator is unable to see diagnostic information for a Cisco Industrial Ethernet switch that has been added to a SIMATIC management station. Based on the provided CLI output, which statement is correct?
switch# show profinet status
State : Enabled
Vlan : 201
Id : IE2000-Switch
Connected : Yes
ReductRatio : 128
GSD version : Mis-match

A.    The assigned ProfiNET VLAN is not valid and should be less than 100
B.    LLDP has been disabled on this switch
C.    The GSD file version on the switch does not match the GSD file version on the management station
D.    The Reduction Ration has been set too low

Valid 200-601 Dumps with VCE and PDF for Free (Question 16 – Question 20)

New 200-601 exam questions from PassLeader 200-601 dumps! Welcome to download the newest PassLeader 200-601 VCE and PDF dumps: http://www.passleader.com/200-601.html (70 Q&As –> 90 Q&As)

P.S. Free 200-601 dumps are available on Google Drive shared by PassLeader: https://drive.google.com/open?id=0B-ob6L_QjGLpekY2NnBTTzFpejQ

QUESTION 16
You have reached the limit of IPv4 IGMP groups available on a Cisco IE 3000 switch that was deployed using the Express Setup. Which CLI command will increase the number of available IPv4 IGMP groups and multicast routes from 256 to 1000 on this switch?

A.    switch(config)#sdm prefer routing
B.    switch(config)#sdm prefer vlan igmp
C.    switch(config)#sdm prefer routing igmp
D.    switch(config)#sdm prefer vlan

New 200-601 Dumps with VCE and PDF from PassLeader (Question 11 – Question 15)

New 200-601 exam questions from PassLeader 200-601 dumps! Welcome to download the newest PassLeader 200-601 VCE and PDF dumps: http://www.passleader.com/200-601.html (70 Q&As –> 90 Q&As)

P.S. Free 200-601 dumps are available on Google Drive shared by PassLeader: https://drive.google.com/open?id=0B-ob6L_QjGLpekY2NnBTTzFpejQ

QUESTION 11
You are called at home at 3am by an unskilled machine operator with a suspected network related problem; the controller LEDs are all normal but the output module’s communications LED is not on. The operator has verfied the cable is functional and correctly connected from the communication module to the switch. What is the next check that you ask the unskilled machine operator to make?

A.    Log onto the switch using the console port and check that IGMP snooping is enabled
B.    Open wireshark and check whether the controller is issuing a forward open instruction to the device
C.    Open the diagnostic faceplate on the HMI for the control panel switch and check that the relevant ports are enabled and not in alarm
D.    Open Studio 5000 and check the module status tab for the affected output module

Free PassLeader 200-601 Exam Dumps with VCE and PDF Download (Question 6 – Question 10)

New 200-601 exam questions from PassLeader 200-601 dumps! Welcome to download the newest PassLeader 200-601 VCE and PDF dumps: http://www.passleader.com/200-601.html (70 Q&As –> 90 Q&As)

P.S. Free 200-601 dumps are available on Google Drive shared by PassLeader: https://drive.google.com/open?id=0B-ob6L_QjGLpekY2NnBTTzFpejQ

QUESTION 6
Which describes the relationship between a workgroup bridge?

A.    Wired clients of a workgroup bridge can communicate, through the workgroup bridge, with wireless clients of an autonomous or a controller-based access point
B.    Wireless clients of a controller-based AP can communicate, through the workgroup bridge, with wireless clients of an autonomous access point
C.    Wireless clients of an autonomous access point can communicate with wired clients of a workgroup bridge, but Wireless clients of a controller-based access point cannot communicate with wired clients of a workgroup bridge
D.    Wireless clients of a controller-based access point can communicate with wired clients of a workgroup bridge, but Wireless clients of an autonomous access point cannot communicate with wired clients of a workgroup bridge

Pages:  1 2