100% Pass Guarantee PassLeader 210-065 Dumps with VCE and PDF for Free (Question 16 – Question 30) – PassLeader New Cisco Exam Dumps – CCNA, CCNP, CCIE, DevNet, CCDE Certification Exam Dumps VCE and PDF and Braindumps and Practice Tests

New 210-065 exam questions from PassLeader 210-065 dumps! Welcome to download the newest PassLeader 210-065 VCE and PDF dumps: http://www.passleader.com/210-065.html (363 Q&As –> 400 Q&As –> 412 Q&As –> 444 Q&As)

P.S. Free 210-065 dumps are available on Google Drive shared by PassLeader: https://drive.google.com/open?id=0B-ob6L_QjGLpfjREa25iSExKUkxvQi12aVdDMWNJSGs0T2JwYkhVUmtwdXhETmZVR3ZNek0

QUESTION 16
Which of these needs to be enabled in Cisco Unified Communications Manager in order for the Cisco TelePresence System 500-32 to be able to share a presentation with a Cisco TelePresence System Codec C40 endpoint that is registered to a VCS?

A.    Allow iX application media
B.    Send send-receive SDP in mid-call invite
C.    Allow presentation sharing using BFCP
D.    Allow presentation sharing using H.235
E.    Deliver conference bridge identifier

Answer: C

QUESTION 17
What is the main difference between a Cisco TelePresence Multipoint Control Unit and a Cisco TelePresence Multipoint Switch?

A.    The Cisco TelePresence Multipoint Control Unit is a hardware bridge.
The Cisco TelePresence Multipoint Switch is a software bridge.
B.    The Cisco TelePresence Multipoint Control Unit is a software bridge for immersive and non-immersive endpoints.
The Cisco TelePresence Multipoint Switch is a hardware bridge for non-immersive endpoints.
C.    The Cisco TelePresence Multipoint Control Unit delivers automatic voice-activated switching.
The Cisco TelePresence Multipoint Switch provides active presence.
D.    The Cisco TelePresence Multipoint Control Unit has a latency of less than 10 ms, whereas the Cisco TelePresence Multipoint Switch has a latency of 100 ms.

Answer: A

QUESTION 18
Which two of these are required in order to complete the password recovery of a Cisco TelePresence System endpoint? (Choose two.)

A.    must have FTP enabled on the endpoint
B.    must have SSH enabled on the endpoint
C.    must have the security question answer for the endpoint
D.    must be in the same room as the main display
E.    must have SFTP enabled on the endpoint
F.    must call Cisco TAC for the security code

Answer: BD

QUESTION 19
In this item, you will need to use all information presented to you to successfully answer the question. Refer to the exhibits. An administrator needs to perform a factory reset on a C-Series endpoint. What are two valid ways to accomplish this task? (Choose two.)

A.    Exhibit A
B.    Exhibit B
C.    Exhibit C
D.    Exhibit D
E.    Exhibit E

Answer: CD

QUESTION 20
Which standard will support call forwarding?

A.    H.450.3
B.    H.323
C.    RFC 2833
D.    H.450.2

Answer: A

QUESTION 21
Which CLI command can be used to reset the Cisco TelePresence System 500-32 personal video system to a factory condition?

A.    utils factory reset 2
B.    utils system factory init
C.    xcommand defaultvalues set level: 2
D.    xconfiguration default factory
E.    utils reset factory
F.    xcommand SystemUnit FactoryReset

Answer: B

QUESTION 22
In this item, you will need to use all information presented to you to successfully answer the question. The C-Series endpoint (codec) does not register with the Video Communication Server that is located in a different network. Based on the exhibits, what could be causing the issue?

A.    The subnet mask on the codec is incorrect.
B.    The ip address of the codec is incorrect.
C.    The interface that the codec is in is in the wrong VLAN.
D.    The codec did not receive a DHCP address from the DHCP server.

Answer: A
Explanation:
The subnet mask configured on the codec is 255.255.255.128, when it should be 255.255.255.0.

QUESTION 23
Which three of these are functions of the Cisco TelePresence Management Suite? (Choose three.)

A.    automatic software update and release keys
B.    intelligent call routing engine
C.    provisioning a Cisco TelePresence System endpoint
D.    tracing SIP and H.323 calls
E.    managing phonebooks for endpoints that are registered to the Cisco Unified Cisco Unified Communications Manager
F.    rebooting endpoints that are registered to the Cisco TelePresence Video Communications Server

Answer: ABF

QUESTION 24
Refer to the exhibit. Which system tab can be used to add video infrastructure devices and endpoints?

A.    Navigator
B.    System Overview
C.    Configuration Templates
D.    Provisioning
E.    Administrative Tools

Answer: A

QUESTION 25
Which two layout or switching modes are supported with the Cisco TelePresence Multipoint Switch? (Choose two.)

A.    enhanced continuous presence
B.    active speaker switching
C.    continuous presence
D.    speaker switching
E.    room switching
F.    active continuous presence

Answer: DE

QUESTION 26
Which Cisco TelePresence Multipoint Control Unit Layout view mode gives prominence to one conference participant over the other conference participants while still allowing conference participants to view multiple participants at the same time?

A.    enhanced continuous presence
B.    active speaker
C.    continuous presence
D.    room switching
E.    speaker switching

Answer: A

QUESTION 27
Which four features are provided by Cisco TelePresence Management Suite? (Choose four.)

A.    Scheduling of video conference calls
B.    Built-in-bridge functionality for multiparty video conferences
C.    SIP-H.323 protocol interworking
D.    Centralized management of conference resources
E.    SMTP email event notification
F.    Endpoint configuration backup and restore
G.    Cisco TelePresence endpoint automated redundancy
H.    Automated resource optimization

Answer: ADEF

QUESTION 28
An important Cisco TelePresence video multipoint call is in progress and you are getting complaints of pixilation of the video and poor audio quality on one of the involved systems. Which page would be a good place to start for troubleshooting the issue on the affected endpoint?

A.    Exhibit A
B.    Exhibit B
C.    Exhibit C
D.    Exhibit D

Answer: A

QUESTION 29
Which two of these support an ad-hoc conference call? (Choose two.)

A.    Cisco TelePresence Multiway with Cisco TelePresence Multipoint Control Unit and Cisco TelePresence Video Communications Server
B.    using the Cisco TelePresence Management Suite Scheduler to schedule a conference call to start in 5 minutes
C.    using the Booking tab in the Cisco TelePresence Management Suite to configure a new conference
D.    using the tab Administrative Tools > Configuration > Conference Settings in the Cisco TelePresence Management Suite
E.    pressing the conference button on a Cisco Unified IP Phone 8941 to conference in a third call

Answer: AE

QUESTION 30
Refer to the exhibit. Which configuration element can be used to specify the Multiway address that can be used by the endpoint to initiate Multiway calls?